5/5 on Google Reviews

Electrical Fault Finding in Montrose

Fault finding, circuit testing and diagnostic investigations for tripping fuse boxes, dead sockets and intermittent electrical faults in Montrose and across Angus. Speak to James Leslie directly and get hidden wiring problems found safely.

Call 01674 900550James answers · 24/7 for emergencies
  • Local, Montrose based electrician
  • Investigation costs agreed before work begins
  • Calibrated test equipment
  • Clear written findings provided
James Leslie

Get your fault finding quote

Emergency or out of hours? Call 01674 900550, 24/7.

No obligation. Investigation costs are agreed before work begins.

  • 18th EditionBS 7671 Qualified
  • City & Guilds2382-22, Level 3
  • Fully InsuredFor Electrical Work
  • RAF ElectricianElectrical Engineer
  • Ex-Retained FirefighterFire & Rescue Service
The Montrose Sparks van parked in Montrose

Electrical Fault Finding Across Montrose, Angus

Montrose Sparks is James Leslie, based in Montrose. Wiring in the older houses and closes around the High Street has often been added to over the years, and coastal damp does outdoor fittings no favours, so faults here are tested for, not guessed at. He covers DD10 and an approximate 40-mile radius.

James carries out the investigation, writes the report and does any repair. If a fault cannot wait, the 24/7 Emergency Electrician page explains how an urgent visit works. Where testing shows the board itself is at fault, a consumer unit replacement is quoted separately. A full inspection of the installation is a separate EICR, not a fault investigation.

5/5 on Google Reviews

★★★★★Google Review
“He took great care over the work (even used a spirit level to make sure the cooker was sitting right!) and was very reasonably priced. We are new to the area and struck lucky finding a reliable, responsive electrician.”
Donna NZVerified
★★★★★Google Review
“Great service, fast response and problem fixed quickly”
Jen JVerified
★★★★★Google Review
“Great service highly recommended.”
Lee DuncanVerified
★★★★★Google Review
“Jamie arrived within 15 minutes of my call and had the power back on about 10 minutes later.”
megan mcgregorVerified
★★★★★Google Review
“James was very polite and sent over the quote immediately after the call and came out the same day in the early evening.”
SamanthaVerified
★★★★★Google Review
“He couldn't of been more helpful and still only took what he quoted for, even though it was a bigger job than expected. Definitely recommend.”
Tammy CrockattVerified
★★★★★Google Review
“Arrived within an hour of my call, as he said he would. Fixed the problem same afternoon, and rate was extremely reasonable!”
Sarah DundasVerified
★★★★★Google Review
“They also give decent price for the job and the work done will be using James again, he is also very polite and very helpful too me.”
katieVerified
★★★★★Google Review
“Fast response during a weekend, put in a temporary fix so we got power back. Excellent service.”
Ian MilneVerified
★★★★★Google Review
“Very professional and courteous. Highly recommend him.”
BuckyVerified
★★★★★Google Review
“James answered my call late at night and went to my property to investigate even though I had never used him before.”
Mohan ThiagarajahVerified

Why Choose Montrose Sparks for Electrical Fault Finding?

  • Montrose Sparks traces electrical faults across Montrose, Angus

    Fault finding, circuit testing and diagnostic investigations for domestic homes, landlords and commercial properties. James works from Montrose and covers an approximate 40-mile radius.

  • Faults are traced with calibrated test equipment by an 18th Edition qualified electrician

    James uses insulation resistance meters, earth loop impedance testers and RCD analyzers to trace the root cause step by step. He does not guess or keep resetting switches.

  • You deal directly with James Leslie, not a call centre

    There is no office between you and the electrician. James has 40 years of electrical engineering experience across military, municipal and private sectors, including service as an RAF electrical engineer and as a retained firefighter.

  • Montrose Sparks is fully insured and locally based

    The business carries public liability cover for domestic, commercial and agricultural properties. Investigation costs are agreed before work begins.

More about James
James carrying out an electrical inspection at a property
Calibrated test equipment, and a written report of what was checked.

Common symptoms

Why Does My Electricity Keep Tripping?

Usually because a protective device is doing its job: an RCD trips when current leaks to earth, and a circuit breaker trips when a circuit is overloaded or short-circuited. Electrical faults—such as an RCD tripping randomly, sockets losing power, or lights flickering—are symptoms of underlying issues inside your walls or appliances. The cause is found by testing, not by guessing.

  • An RCD that trips randomly

    Hidden neutral-to-earth faults, moisture ingress in outdoor cables or a failing internal appliance element can all trigger the main safety switch.

  • A circuit breaker that keeps tripping

    Nuisance tripping is a symptom, not the fault. Repeatedly resetting the switch can lead to wire melting or electrical fires.

  • Power that comes and goes in specific rooms

    Loose connections, high-resistance joints or burnt cables behind faceplates cause unexpected loss of power.

  • Dead sockets or flickering lights

    Traced with calibrated insulation resistance, earth loop impedance and RCD testing rather than guesswork.

Keeps tripping? Tell James what happens and when.

Signs You Should Stop Resetting and Call

Guessing or repeatedly resetting switches can lead to wire melting or electrical fires. If any of the following applies, leave the circuit off and call James rather than trying the switch again:

  • A breaker that trips immediately on reset

    A device that will not stay on, or trips the instant it is reset, is usually holding a live fault on that circuit. Leave it off and have the circuit tested.

  • Warm or discoloured sockets and switches

    Heat, browning or a faceplate that has started to distort can indicate a loose or high-resistance connection behind it. Stop using the accessory and do not touch it to check its temperature.

  • A burning smell or buzzing from the board or a fitting

    A hot-plastic smell, crackling or a hum from the consumer unit, a socket or a light fitting needs urgent assessment. Switch off at the main switch if it is safe to reach and keep clear.

  • Water near electrics

    A leak into a light fitting, a socket, an outdoor cable or the consumer unit is a common cause of RCD tripping and a risk while the circuit stays live. Leave it off until it has been inspected and dried out.

Call 01674 900550Not sure whether it can wait? Phone and describe what is happening.

Uncovering Hidden Wiring Faults Safely

Using advanced calibrated test equipment (insulation resistance meters, earth loop impedance testers, and RCD analyzers), James Leslie systematically traces the root cause of electrical faults.

  • James listening to a homeowner in her kitchen

    Tripping RCD & Nuisance Circuit Breaker Tracing

    Locating hidden neutral-to-earth faults, moisture ingress in outdoor cables, or failing internal appliance elements that trigger main safety switches.

  • dead socket being investigated

    Intermittent Power Loss & Dead Sockets

    Tracing loose connections, high-resistance joints, or burnt cables behind faceplates that cause unexpected loss of power to specific rooms.

  • James reviewing notes and a phone at a kitchen table

    Private Written Investigation Reports & Photo Proof

    Following testing, you receive a clear written report explaining what was checked, photographic proof of any damaged cables found, and an upfront quote for permanent repairs.

Fault finding cost guide

How Much Does Electrical Fault Finding Cost?

£80 – £500+ for an electrical fault investigation. Investigation costs agreed before work begins. Clear written findings provided.

Electrical Fault InvestigationTime needed to trace fault, circuit access, testing complexity. Investigation scope agreed by phone before visit.
£80 – £500+Scope agreed by phone before visit

Indicative guide prices. The final scope and cost are agreed before work begins.

Full pricing guide

How it works

How Is an Electrical Fault Traced?

A fault investigation works from the symptoms to the cause, one circuit at a time. What each visit involves:

  1. 1

    Describe the symptoms and when they started

    Which device trips, which rooms or sockets are affected, whether it happens with a particular appliance, in wet weather or at a certain time of day. This narrows the search before the visit and sets the investigation scope, which is agreed by phone.

  2. 2

    Isolate and inspect the consumer unit and affected accessories

    With the supply safely isolated, the board, the tripping device and the sockets, switches and fittings on the affected circuit are opened up and inspected for loose terminals, heat damage, moisture and past alterations.

  3. 3

    Test the circuit to narrow the fault

    Insulation resistance, continuity and RCD operation are measured with calibrated test equipment. Splitting the circuit and retesting shows which section, joint or appliance is responsible.

  4. 4

    Make safe, or repair where agreed

    A confirmed fault is either repaired on the spot, where the parts are to hand and the cost has been agreed, or isolated and made safe with a quote for the permanent repair.

  5. 5

    Report the findings and next steps in writing

    You receive a written note of what was checked, what was found, what was done and what remains outstanding, with photographs of any damaged cables and a recommendation for what to do next.

Small repairs found during an investigation, such as a replacement socket or switch, are covered under Small Electrical Repairs.

After testing

Private Written Investigation Reports & Photo Proof

Following testing, you receive a clear written report explaining what was checked, photographic proof of any damaged cables found, and an upfront quote for permanent repairs.

  • Written Investigation Report

    A clear written report explaining what was checked, the findings, any work completed during the visit, anything left outstanding and the recommended next steps. Test readings are noted where they support the finding.

  • Photographic Proof

    Photographic proof of any damaged cables found, taken during the investigation so you can see what was behind the fault before it is repaired or covered over.

  • Upfront Quote for Permanent Repairs

    An upfront quote for permanent repairs, with costs agreed before any work begins. Where a repair is completed on the visit, the report records it; anything else is quoted for your approval.

Related Inspections & Protection

A fault investigation looks at the circuits showing symptoms. A full inspection of the fixed installation is a separate job under Landlord EICRs, and protection for electronics and appliances is covered under Surge Protection.

Electrical Fault Finding Across Montrose, Angus

Tripping RCDs, dead sockets and intermittent power are investigated from Montrose, Angus, Scotland, across the DD10 postcode district, the Angus towns and the Mearns within an approximate 40-mile radius. Give James your postcode and describe the fault, and he will confirm availability.

  • Montrose and DD10The town, Ferryden and Hillside, and up the coast to St Cyrus. Our base, so usually the quickest to arrange.
  • Brechin and ForfarHomes, rentals and business premises across the Angus towns.
  • ArbroathFault investigations and repairs, including surrounding rural properties.
  • Laurencekirk and InverbervieEnquiries welcome for houses, flats and rented properties.
  • Elsewhere in Angus and the MearnsDundee and Stonehaven are inside the approximate 40-mile service area. Call with your postcode to check coverage.
Map of the Montrose Sparks service area: about 40 miles around Montrose, across Angus and the Mearns to DundeeNorth Sea10 mi20 mi30 mi40-MILE SERVICE AREABrechinForfarArbroathDundeeKirriemuirLaurencekirkCarnoustieStonehavenInverbervieMontrose

Inside the service area

Brechin

About 7 miles from Montrose, as the crow flies

Call 01674 900550

Frequently Asked Questions About Electrical Fault Finding

Can’t see your question?

James answers the phone himself and will tell you straight away whether he can help.

Call 01674 900550
Why does my RCD keep tripping?

An RCD trips when it detects current leaking to earth, so repeated tripping usually means something on the protected circuits is leaking. Common causes include a faulty appliance, moisture in an outdoor cable or fitting, a neutral-to-earth fault in the wiring or, less often, a worn RCD itself. Unplugging appliances one at a time can point to a faulty appliance, but a wiring fault can only be confirmed by testing. James tests the circuits and reports what was found.

Is a tripping circuit breaker dangerous?

The trip itself is the breaker doing its job: it has disconnected a circuit that was overloaded or had a fault. What needs attention is the cause. A breaker that trips repeatedly, or will not stay on when reset, indicates a fault that has not gone away, and repeatedly resetting it can lead to wire melting or electrical fires. Leave the circuit off and arrange an investigation.

Why do my lights flicker?

Flickering can have several causes, from a loose connection at a switch, fitting or in the consumer unit to a lamp or dimmer that is not compatible, or a problem with the incoming supply. Flickering confined to one fitting is often local to it; flickering across several rooms is more likely a connection or supply issue and should be investigated rather than assumed. James traces where the flicker originates and explains what he finds.

Can you find a fault the same day?

Sometimes, but it is not something that can be promised. It depends on availability on the day and on the fault itself: some are traced and repaired on the first visit, while an intermittent fault or one needing parts can take more than one. Investigation scope agreed by phone before visit. For a fault that cannot wait, phone to check the next available visit.

Will I get a report?

Yes. Following testing, you receive a clear written report explaining what was checked, photographic proof of any damaged cables found, and an upfront quote for permanent repairs. It also notes any work completed on the visit and anything left outstanding, so you have a record for your own files, a landlord or a letting agent.

Do I need a full EICR or just fault finding?

Fault finding is the right job when something specific is wrong: a device that trips, a dead socket or power that comes and goes. It looks at the circuits showing symptoms and aims to find and fix the cause. An EICR is a condition inspection of the whole fixed installation, reported against the wiring regulations, and does not repair anything. If a fault investigation uncovers wider concerns about the installation, James says so and a full inspection can be quoted separately.

Get your fault finding quote

Send your address and say what is happening and how often. James agrees the scope of the investigation with you by phone before he visits.

James aims to reply within one hour, 8am–6pm.

Tap to call 01674 900550
James Leslie

Get a free quote

Replies within an hour, 8am–6pm.

Emergency or out of hours? Call 01674 900550, 24/7.

No obligation. Costs are agreed before any work begins.