5/5 on Google Reviews

Immersion Heater Repairs in Montrose

When the immersion heater stops giving you hot water, James can investigate the electrical supply and the controls. You find out what the fault is before you decide between repair and replacement.

Call 01674 900550James answers · 24/7 for emergencies
  • Supply, switch, timer and thermostat checked first
  • Element and thermostat faults repaired where they are electrical
  • Off-peak and timed supplies understood
  • Costs agreed before work begins
James Leslie

Get your immersion heater repair quote

Emergency or out of hours? Call 01674 900550, 24/7.

No obligation. Costs are agreed before any work begins.

  • 18th EditionBS 7671 Qualified
  • City & Guilds2382-22, Level 3
  • Fully InsuredFor Electrical Work
  • RAF ElectricianElectrical Engineer
  • Ex-Retained FirefighterFire & Rescue Service
The Montrose Sparks van parked in Montrose

Immersion Heater Faults in Montrose, Angus

Montrose Sparks is James Leslie, based in Montrose. He looks at immersion heaters in flats and houses in the town, in the villages of DD10 and on the farms and rural properties beyond, within an approximate 40-mile radius.

In many Angus homes without gas the immersion heater is the only source of hot water, so a cold cylinder needs fixing, not working around. James investigates the electrical side and tells you when another trade or further work is needed. Heaters on the same off-peak supply come under Storage Heater Repairs & Replacement, faults that reach beyond the immersion circuit under Electrical Repairs & Fault Finding, and other small jobs under Small Electrical Repairs.

5/5 on Google Reviews

★★★★★Google Review
“He took great care over the work (even used a spirit level to make sure the cooker was sitting right!) and was very reasonably priced. We are new to the area and struck lucky finding a reliable, responsive electrician.”
Donna NZVerified
★★★★★Google Review
“Great service, fast response and problem fixed quickly”
Jen JVerified
★★★★★Google Review
“Great service highly recommended.”
Lee DuncanVerified
★★★★★Google Review
“Jamie arrived within 15 minutes of my call and had the power back on about 10 minutes later.”
megan mcgregorVerified
★★★★★Google Review
“James was very polite and sent over the quote immediately after the call and came out the same day in the early evening.”
SamanthaVerified
★★★★★Google Review
“He couldn't of been more helpful and still only took what he quoted for, even though it was a bigger job than expected. Definitely recommend.”
Tammy CrockattVerified
★★★★★Google Review
“Arrived within an hour of my call, as he said he would. Fixed the problem same afternoon, and rate was extremely reasonable!”
Sarah DundasVerified
★★★★★Google Review
“They also give decent price for the job and the work done will be using James again, he is also very polite and very helpful too me.”
katieVerified
★★★★★Google Review
“Fast response during a weekend, put in a temporary fix so we got power back. Excellent service.”
Ian MilneVerified
★★★★★Google Review
“Very professional and courteous. Highly recommend him.”
BuckyVerified
★★★★★Google Review
“James answered my call late at night and went to my property to investigate even though I had never used him before.”
Mohan ThiagarajahVerified

Why Choose Montrose Sparks for Immersion Heater Repairs?

  • Montrose Sparks investigates immersion heater faults across Montrose, Angus

    James investigates the electrical symptoms first and then explains what needs repairing. He is based in Montrose and serves homes, farms and businesses across Angus and surrounding areas within approximately 40 miles.

  • Work is carried out to BS 7671 by an 18th Edition qualified electrician

    Controls and replacement components have to suit the particular cylinder and installation. Plumbing work and the replacement of wet components must be agreed separately from the electrical investigation.

  • You deal directly with James Leslie, not a call centre

    James Leslie is based in Montrose and picks up the phone himself. Behind him are 40 years of electrical engineering experience, time as an RAF electrical engineer and service as a retained firefighter.

  • Montrose Sparks is fully insured and locally based

    James holds public liability insurance for work in domestic, commercial and agricultural properties. Costs are agreed before any work begins.

More about James
James carrying out an electrical inspection at a property
Small jobs are welcome, with clear explanations and costs agreed before work begins.

Before replacing anything

Does No Hot Water Mean the Cylinder Needs Replacing?

Not necessarily. Supply or control faults may be involved. James investigates the electrical side and explains when another trade or further work is needed. A cold cylinder does not by itself identify the faulty component.

  • Is the supply reaching the heater?

    A switched-off isolator, a tripped breaker or a loose connection at the switch or the cylinder can leave the water cold with nothing wrong with the heater itself. This is the first thing checked.

  • Is the timer or thermostat calling for heat?

    A timer that has lost its programme, a thermostat that has failed or been turned down, or off-peak switching that is no longer operating can all stop the element being energised even though the supply is healthy.

  • Has the element failed?

    An element can fail so that it no longer heats, or break down so that it trips the circuit as soon as it is switched on. Testing at the cylinder shows which, and whether the fault is in the element, the thermostat or the wiring to it.

  • Is it the cylinder rather than the electrics?

    Leaks, scale, a failed cylinder or a problem with the pipework are plumbing matters. Where the electrical checks show the heater and its controls are working, James explains what has been found so a plumber can take it from there.

Not sure which part has failed? Describe the symptoms.

Signs the Fault Is Electrical

Not every cold cylinder is an electrical fault, but the signs below usually point to the supply, the controls or the element rather than the cylinder. Do not bypass a thermostat or safety cut-out, and avoid repeated resets. Switch the heater off and tell James what you have noticed.

  • No heat with the switch on

    If the immersion switch is on and the water stays cold, the supply, the thermostat or the element may have failed. A lit switch on its own does not confirm that power is reaching the element.

  • Heats only on one setting or timer

    A cylinder that heats on boost but not during the off-peak period, or on one element but not the other, tends to point to a timer, an off-peak switch or one element rather than the cylinder. Say which setting works when you call.

  • The breaker trips when it runs

    An element that has broken down can trip the RCD or breaker as soon as the immersion is switched on. Leave it off rather than resetting it; the element and its wiring need testing before it is used again.

  • Scorching or a smell at the switch

    Discolouration, a burning smell or warmth at the immersion switch or the cylinder connection can indicate a loose or overheating connection. If it is safe to do so, switch the heater off at its isolator and arrange a check before using it again.

Call 01674 900550Switch the immersion off at its isolator and describe the symptoms to James.

What Immersion Heater Fault Finding Covers

The electrical side of an immersion heater runs from the isolator or timer, through the thermostat, to the element in the cylinder. James checks each in turn and explains where the electrical work stops and plumbing begins.

  • James looking around a finished bathroom

    Supply and control checks

    A failed timer, supply connection, thermostat or heating element may be involved when an immersion heater stops working. James investigates the electrical symptoms before explaining what needs repair. A cold cylinder does not by itself identify the faulty component.

  • off-peak immersion heater timer switch

    Timers, thermostats and off-peak supplies

    Tell James whether the heater uses a boost control, an off-peak supply or more than one element. Recent meter, tariff or control changes may help explain when the fault started. Controls and replacement components need to suit the particular cylinder and installation.

  • immersion heater isolator switch in a cylinder cupboard

    Electrical repairs and cylinder work

    Access to an element can involve draining the cylinder and plumbing work. Agree those arrangements separately from electrical fault finding. Unvented hot-water systems have additional safety requirements and may need an appropriately qualified hot-water specialist.

How Are Immersion Heater Repairs Priced?

There is no fixed price for an immersion heater repair, because the fault has to be found before the work can be scoped. What you can expect is set out below.

  • Quoted after assessment

    Quote agreed after assessment. The equipment, access, investigation needed and extent of installation or repair affect the price.

  • Costs agreed before work begins

    James explains the proposed work and any additional costs before you agree to proceed.

  • Plumbing work agreed separately

    Describe which heating controls you use and whether the fault affects all hot water. Plumbing work and replacement of wet components must be agreed separately from electrical investigation.

Preparing for an Investigation

Share the cylinder and control details, the symptoms and any recent changes. Do not bypass a thermostat or safety cut-out, and avoid repeated resets. If there are signs of overheating or leaking near electrical equipment, stop using the affected equipment and call for advice.

Useful to have ready

  • Where the cylinder is and how it is reached

  • Which controls you use: wall switch, timer, boost button or an off-peak supply

  • Whether the fault affects all hot water or only at certain times

  • Any recent meter, tariff or control changes

Describe the symptoms and James will quote the investigation.

How Is an Immersion Heater Fault Repaired?

The fault is traced from the supply towards the cylinder, so the part that has actually failed is identified before anything is replaced.

  1. 1

    Check the supply, switch, timer and thermostat

    James confirms power is reaching the isolator and the immersion switch, checks that the timer or off-peak switching is operating and looks at how the thermostat is set and whether it is calling for heat.

  2. 2

    Isolate the circuit

    The immersion heater circuit is switched off at the consumer unit and proved dead before any cover is removed at the switch or the cylinder.

  3. 3

    Test the element and thermostat

    The element is tested for continuity and insulation resistance and the thermostat for correct switching. This shows whether the fault is in the element, the thermostat, the control or the wiring, rather than guessing from the symptoms.

  4. 4

    Replace the electrical part where agreed

    A failed thermostat, switch, timer or the wiring to the cylinder is repaired or replaced once the cost is agreed. Access to an element can involve draining the cylinder and plumbing work. Agree those arrangements separately from electrical fault finding.

  5. 5

    Test and confirm the hot water arrangement with you

    The repaired circuit is tested, the heater is run and James goes through the arrangement with you: which switch or timer does what, and when the cylinder should be heating.

Where the fault turns out to be in the cylinder itself, or the system is unvented, James explains what has been found and ruled out so the right trade can take it on.

On completion

What you are left with

The paperwork for an immersion heater repair depends on whether the circuit has been altered and whether anything has been referred on. James confirms what is issued for your job.

  • Minor Electrical Installation Works Certificate

    Where the repair alters or replaces part of the immersion heater circuit, a Minor Electrical Installation Works Certificate records the work carried out and the test results for that circuit. Its scope is limited to the circuit worked on.

  • A note of anything referred on

    If the investigation shows the problem is in the cylinder, the pipework or an unvented system, James explains what has been checked and what has been ruled out, so a plumber or hot-water specialist can take it from there without repeating the electrical tests.

Immersion Heater Repairs Across Montrose, Angus

Immersion heaters are common in homes without a gas supply, in properties on off-peak tariffs and in rural parts of Angus, so many of these calls come from outside the main towns. James is based in Montrose, Angus, Scotland, and covers the DD10 postcode district, the Angus towns and the Mearns within an approximate 40-mile radius. Give him your postcode to confirm availability.

  • Montrose and DD10The town, Ferryden and Hillside, and up the coast to St Cyrus. Our base, so usually the quickest to arrange.
  • Brechin and ForfarHomes, rentals and business premises across the Angus towns, including flats with electric-only hot water.
  • ArbroathImmersion heater and other electrical repairs, including surrounding rural properties without a gas supply.
  • Laurencekirk and InverbervieEnquiries welcome for houses, flats and rented properties.
  • Elsewhere in Angus and the MearnsDundee and Stonehaven are inside the approximate 40-mile service area. Call with your postcode to check coverage.
Map of the Montrose Sparks service area: about 40 miles around Montrose, across Angus and the Mearns to DundeeNorth Sea10 mi20 mi30 mi40-MILE SERVICE AREABrechinForfarArbroathDundeeKirriemuirLaurencekirkCarnoustieStonehavenInverbervieMontrose

Inside the service area

Brechin

About 7 miles from Montrose, as the crow flies

Call 01674 900550

Frequently Asked Questions About Immersion Heater Repairs

Can’t see your question?

James answers the phone himself and will tell you straight away whether he can help.

Call 01674 900550
Does no hot water mean the cylinder needs replacing?

Not necessarily. Supply or control faults may be involved. James investigates the electrical side and explains when another trade or further work is needed.

Why is my immersion heater not heating the water?

It may be the supply, the thermostat, the timer or the element, and the symptoms alone rarely say which. A tripped breaker or a switched-off isolator leaves the cylinder cold with nothing wrong with the heater; a failed thermostat or a timer that has lost its programme stops the element being energised; a failed element does not heat even when everything else is working. James tests each in turn and explains which has failed before any part is replaced.

Can an immersion heater element be replaced?

Yes. The element is an electrical component and a failed one can be replaced, but it also sits in the water. Access to an element can involve draining the cylinder and plumbing work. Agree those arrangements separately from electrical fault finding. Unvented hot-water systems have additional safety requirements and may need an appropriately qualified hot-water specialist. James explains which arrangement applies to your cylinder before anything is agreed.

Is it safe to leave the immersion on all the time?

Where the thermostat and any safety cut-out are working, an immersion heater is designed to switch itself off once the water reaches temperature, so leaving it switched on is not in itself a safety problem. Whether it suits you depends on how you use hot water and whether a timer or off-peak supply would heat the cylinder at a better time. Do not bypass a thermostat or safety cut-out, and avoid repeated resets. If the heater seems to run without stopping or the water gets very hot, the thermostat may have failed and needs checking.

Can you fix an immersion heater on an off-peak tariff?

Yes. Tell James whether the heater uses a boost control, an off-peak supply or more than one element. Recent meter, tariff or control changes may help explain when the fault started. Controls and replacement components need to suit the particular cylinder and installation. Where the off-peak switching is done at the meter, James explains what he can repair and what needs to go to your supplier.

Do I need a plumber or an electrician?

It depends on where the fault is. The supply, isolator, timer, thermostat and the wiring to the element are electrical work. Access to an element can involve draining the cylinder and plumbing work. Agree those arrangements separately from electrical fault finding. James investigates the electrical side and explains when another trade or further work is needed.

Will you leave me a certificate?

Where the repair alters or replaces part of the circuit, you receive a Minor Electrical Installation Works Certificate recording the work and the test results for that circuit. A fault find that changes nothing may not need one; James confirms what is issued for your job. Anything referred on for plumbing or cylinder work is noted so the next trade knows what has been ruled out.

Get your immersion heater repair quote

Say which heating controls you use and whether the fault affects all of your hot water. Include the cylinder and control details, the symptoms and anything that changed recently.

James aims to reply within one hour, 8am–6pm.

Tap to call 01674 900550
James Leslie

Get a free quote

Replies within an hour, 8am–6pm.

Emergency or out of hours? Call 01674 900550, 24/7.

No obligation. Costs are agreed before any work begins.